An AI physics tutor that draws the forces first

It sets up each problem on a whiteboard, one arrow and one line at a time, then asks you to set up the next one yourself.

Free plan with 50 credits a month. Add your materials once you're in.

  • 3,300+ learners
  • 15,000+ tutoring sessions
  • Cancel anytime
  • Nothing to install

The same lesson, written out

This is a common exam question because no single formula gives the answer: you have to decide whether the block moves before you know which friction rule applies. On Sitor the tutor builds the solution in steps on the whiteboard and asks you to predict each one before it is drawn.

The question

A 2.0 kg block is placed at rest on a ramp inclined at 30° to the horizontal. The coefficients of friction between the block and the ramp are μs = 0.70 (static) and μk = 0.50 (kinetic). What is the friction force on the block? Use g = 9.8 m/s².

Your turnCheck yourself: the same ramp is raised to 40°. Does the block slide now, and if so, what is its acceleration?Show the answer

Yes. The pull down the ramp is mg sin 40° = 19.6 N × 0.643 = 12.6 N. The normal force is mg cos 40° = 19.6 N × 0.766 = 15.0 N, so static friction can supply at most 0.70 × 15.0 N = 10.5 N, which is not enough. Once the block slides, friction is kinetic, f = μk N, and Newton's second law along the ramp gives a = g (sin 40° − μk cos 40°) = 9.8 m/s² × (0.643 − 0.383) ≈ 2.5 m/s² down the ramp.

  1. Draw the free-body diagram

    Three forces act on the block, and only three: its weight mg = 2.0 kg × 9.8 m/s² = 19.6 N straight down, the normal force N perpendicular to the ramp, and friction f along the ramp. Friction points up the ramp, because it opposes the slide that would happen without it.

  2. Choose axes along and across the ramp

    Tilt the axes: x points down the ramp, y points out of its surface. Now N and f each lie on one axis and only the weight has to be split. Its component along the ramp is mg sin θ = 19.6 N × 0.500 = 9.8 N, and its component into the ramp is mg cos θ = 19.6 N × 0.866 = 17.0 N.

  3. Newton's second law across the ramp

    The block neither lifts off the ramp nor sinks into it, so the acceleration along y is zero: N − mg cos θ = 0, which gives N = 17.0 N. The normal force is not mg here. On an incline it is smaller than the weight.

  4. Ask whether the block slides at all

    Static friction supplies whatever force is needed to prevent sliding, up to a maximum of μs N = 0.70 × 17.0 N = 11.9 N. Holding this block still takes only 9.8 N. Since 9.8 N ≤ 11.9 N, the block stays at rest and the kinetic coefficient never enters the problem.

  5. Newton's second law along the ramp

    At rest, the acceleration along x is zero: mg sin θ − f = 0, so f = 9.8 N, directed up the ramp. The two common wrong answers are 11.9 N (μs N, which is only the maximum) and 8.5 N (μk N, which applies only while the block is sliding).

  6. Check the limits

    On a level surface θ = 0 and f = mg sin 0 = 0, which is right: a block on a flat table needs no friction to stay put. Slipping begins when mg sin θ = μs mg cos θ, that is when tan θ = μs = 0.70, or θ ≈ 35°. The mass cancels, and 30° is below 35°, so the answer is consistent.

What makes college physics hard, and how Sitor teaches it

Intro physics has few equations and many ways to misapply them. Most lost points trace back to a belief about motion that feels right and is wrong. In the six topics below, a diagram drawn first changes the answer.

TopicWhere students lose pointsHow Sitor teaches it
Kinematics and projectile motionVelocity and acceleration get confused. Students say the acceleration is zero at the top of a throw, or that a negative acceleration always means slowing down.The board draws the velocity arrow and the acceleration arrow at five points along the path, with the position, velocity and acceleration graphs stacked underneath, then asks what each one is at the highest point.
Free-body diagrams and Newton's lawsThe belief that a force is needed to keep an object moving. Students add a force in the direction of motion, draw "ma" as if it were a force, or treat the normal force and gravity as a third-law pair.Every problem starts with the object drawn alone and one arrow per interaction, each labeled with what exerts it. If you cannot name the object doing the pushing or pulling, the arrow comes off the board.
Friction, normal force and inclinesTwo habits cost the points: writing N = mg on every surface, and writing f = μN even when the object is not sliding. Static friction is only as large as it needs to be, up to μs N.The tutor tilts the axes along the ramp, splits the weight into mg sin θ and mg cos θ, finds N from the perpendicular axis, and asks "does it move?" before any friction value is written.
Circular motionStudents draw a "centripetal force" as an extra arrow, or an outward "centrifugal force", instead of asking which real forces add up to mv²/r toward the center.The same free-body diagram is drawn at the top and at the bottom of a vertical loop, the net force toward the center is set equal to mv²/r each time, and you are asked where the normal force is larger and why.
Energy and momentum in collisionsThe wrong conservation law is chosen. Kinetic energy is assumed conserved in a collision where the objects stick together, or momentum is applied to a system with a net external force on it.Before any equation the tutor draws a boundary around the system and a before-and-after sketch, then asks what crosses the boundary. A ballistic pendulum is split into two stages: momentum for the collision, energy for the swing.
Rotation and torqueTorque is treated as another word for force. Students forget the lever arm, switch pivot points partway through, or leave out the rotational kinetic energy ½Iω² of a rolling object.The board marks the pivot first, draws each lever arm as a perpendicular distance from it, and builds Στ = Iα beside ΣF = ma so the two can be compared line by line. Then: which reaches the bottom of a ramp first, a hoop or a solid disk?

A three-week study plan for a physics exam

A plan for a physics midterm or final that covers four to six chapters. Tell Sitor your exam date and it builds this from your own syllabus; the shape stays the same.

  1. 3 weeks out

    Find the gaps

    • Upload the lecture slides for every chapter on the exam, plus the formula sheet if your course gives one.
    • Take the diagnostic and answer "not sure" honestly, especially on questions where you know the equation but not when it applies.
    • Let the plan put the weakest chapters first. If forces are among them, start there, because circular motion and rotation reuse the same diagrams.
  2. 2 weeks out

    Learn the setups

    • One principle a day on the whiteboard: Newton's second law, work and energy, momentum, rotation.
    • For every problem, draw the diagram, name the system and say which principle applies before writing an equation.
    • Solve in symbols first and put the numbers in on the last line, then check the units.
  3. 1 week out

    Practice mixed problems

    • Ask for exam-style problems that mix chapters, so nothing tells you whether to use forces, energy or momentum.
    • Work each one on paper from a blank page, with a time limit, before looking at any solution.
    • Work any past papers your course has published and check your answers against its solutions.
  4. The last two days

    Review, do not cram

    • Do the spaced reviews waiting on your Today page.
    • Redo, from a blank page, the three problems you got most wrong.
    • Read your formula sheet and say, for each equation, when it does not apply.
    • Sleep. A clear head sets up problems better than one more late hour does.

Common mistakes when studying physics

Reading worked solutions and calling it practice
A solution you follow line by line feels like one you could have written. The exam gives you a blank page, so practice starting from one: cover the solution and produce the diagram and the first equation yourself.
Starting with an equation instead of a diagram
Searching the formula sheet for an equation with the right letters works on homework from a single chapter and fails on an exam. Decide what the system is and which principle applies first. The equation follows from that.
Putting numbers in on the first line
Early numbers hide the structure of the answer. A symbolic result such as a = g (sin θ − μk cos θ) can be checked for units and for limits like θ = 0, and it shows that the mass cancels. A string of decimals shows nothing.
Practicing one chapter at a time until the end
Inside the momentum chapter, every problem is a momentum problem. On the exam, choosing between forces, energy and momentum is the hard part, and only mixed practice trains it.

Start free. Upgrade when it earns its place.

  • Free

    $0

    Monthly credits
    50/mo
    Learning topics
    Up to 10

    Enough to work through a few topics and see if it suits how you study.

  • Pro

    $19.90/mo

    First month $9.90, then $19.90/mo

    Monthly credits
    1,000/mo
    Learning topics
    Up to 500

    For exam season: the most credits plus deep research.

Start free

Questions about studying physics with an AI tutor

Can an AI tutor really teach college physics?

For an introductory course, yes: the mechanics, thermodynamics and circuits of a first-year course are well-established, and an AI tutor can explain, draw and question you on them at any hour. Sitor is a tutor, not an official question bank, and it does not replace your professor, your labs or the past papers your course provides. Like any AI it can make an arithmetic slip, so check numerical results against the answers from your course.

Does it work with my course, such as PHYS 101, PHYS 121, AP Physics 1 or AP Physics C?

Yes. Upload the slides, notes or textbook chapters your course uses and Sitor builds the study plan and the practice questions from those pages, so the notation, sign conventions and scope match what you will be examined on. Without uploads it teaches from a standard introductory physics syllabus.

How is this different from asking ChatGPT to solve a physics problem?

A chatbot solves the problem you paste in, and reading a finished solution is not the same as being able to start one. Sitor starts with a diagnostic, plans the whole syllabus, and teaches each topic step by step on a whiteboard. It asks you to choose the system and the principle rather than only answering, keeps track of what you have mastered, and brings topics back for review before you forget them.

Can it draw free-body diagrams?

Yes. The tutor draws the object, each force, the axes and the components on the whiteboard as it speaks, one arrow at a time, and writes questions on the board for you to answer, such as which way friction points. You can pause, ask about any step, or switch to a text chat. You can also upload a photo of a diagram from your notes and ask about any part of it.

Does it handle calculus-based physics and topics beyond mechanics?

Yes. For a calculus-based course such as PHYS 121 or AP Physics C, the same setups are written with derivatives and integrals: velocity as dx/dt, work as the integral of force over distance. Sitor also teaches the usual later topics, including the second law of thermodynamics and entropy, and basic circuits with Ohm's law and Kirchhoff's rules. Upload your syllabus or slides to keep the scope the same as your course.

How much does it cost?

There is a free plan with 50 credits a month. A turn in the text chat starts at 1 credit and a turn on the whiteboard uses 10, so the free plan covers a short whiteboard lesson or a longer chat session. Starter is $9.90 a month and Pro is $19.90 a month, with a discount on the first month. You can cancel at any time.

Which part of physics are you stuck on?

Free plan with 50 credits a month. Add your materials once you're in.